Hey Seth.....

[Jim]

Seth can you do me a favor and measure your rear driveshaft on your 5sp for me? I need the overall length from the locations pictured. Precision would be appreciated :smilielol: Thanks.


From:
http://i100.photobucket.com/albums/m13/signal73/driveshaft001.jpg




To:

http://i100.photobucket.com/albums/m13/signal73/driveshaft002.jpg

[95ctd]

i could do that, its gonna have to wait till theres light out though, or I'll be down sat if you wanna check it yourself too

[Jim]

No problem on waiting til light out. Im gonna drop it off at the driveshaft shop on fri i was thinking.

[Diesel97]

i could do that, its gonna have to wait till theres light out though, or I'll be down sat if you wanna check it yourself too

I got a flashlight you can borrow if you need it.:dunno:

[95Cummins]

Seth can't do that sorta stuff, he took electronics shop. :poke: :falldownlaugh:

[nfkfirefighter]

a tape what.. who.. he only knows things if there like micro or macro or some crazy stuff like that.. and percision is in like 1/16th of an inches not just in inches

[Jim]

I got a flashlight you can borrow if you need it.:dunno:

Seth can't do that sorta stuff, he took electronics shop. :poke: :falldownlaugh:

a tape what.. who.. he only knows things if there like micro or macro or some crazy stuff like that.. and percision is in like 1/16th of an inches not just in inches

:smilielol: its ok he knows how to order a friggen killer grinder though! :exactly:

[95Cummins]

haha Carbones. Used to be the hot spot after school. Good times :HoleShotHolset:

[killed300ex]

57 5/8 on my truck but a dana 80 might change that

[Sootin]

Dave and Tony just rippin' on Seth.:falldownlaugh:

[Jim]

57 5/8 on my truck but a dana 80 might change that

yeah dana 80 will shorten it up some, I think about 1 1/2" thanks evan

[Warpig]

Dave and Tony just rippin' on Seth.:falldownlaugh:

Who's Tony?? :dunno:

[95Cummins]

nfkfirefighter, Tim. :HoleShotHolset:

[Warpig]

Oh,ok!! Hi Tony :HoleShotHolset:

[BelgianMagic]

Oh,ok!! Hi Tony :HoleShotHolset:

DUMB AZZ :bigfinger::withstupid::ShizenWinder:

[BelgianMagic]

HEY TIM...:warpig:,

Springfield XD making a XDM 45 yet ??

I have a XD 45 ... want an "M"

[Warpig]

HEY TIM...:warpig:,

Springfield XD making a XDM 45 yet ??

I have a XD 45 ... want an "M"

Glock, Glock, Glock :exactly:

[95Cummins]

Hey Jim, if Seth can't get it would an 02 RC 4x4 dualie with a 5spd be the same? We have one at the shop I work at that we have to do a pinion seal on tomorrow and i can measure it real quick.

[ktmcowboy]

hey jim if ya want i have to rebuild my shafts, gunna do it sometime this comin up week and can do it most likely free of labor charge for ya. used to work for a shop that im welcome to do work at......so if ya want and someone could get it to me, or i could meet ya somewhere i could do it for ya. cuz like i say, i gotta do mine too......

[killed300ex]

hey jim if ya want i have to rebuild my shafts, gunna do it sometime this comin up week and can do it most likely free of labor charge for ya. used to work for a shop that im welcome to do work at......so if ya want and someone could get it to me, or i could meet ya somewhere i could do it for ya. cuz like i say, i gotta do mine too......

Think hes looking for more than a rebuild more like adding an inch or two to the driveshaft

[Jim]

HEY TIM,

Springfield XD making a XDM 45 yet ??

I have a XD 45 ... want an "M"

Glock, Glock, Glock

:wtf2: :wtf2: Thread hijack!


hey jim if ya want i have to rebuild my shafts, gunna do it sometime this comin up week and can do it most likely free of labor charge for ya. used to work for a shop that im welcome to do work at......so if ya want and someone could get it to me, or i could meet ya somewhere i could do it for ya. cuz like i say, i gotta do mine too......

I need to add some inches to the rear one. Do you have any experience with rebuilding the front with the double cardigan joint? If so i will take u up on that offer as the one I have is pretty shot. the rear joints are almost new.

Hey Jim, if Seth can't get it would an 02 RC 4x4 dualie with a 5spd be the same? We have one at the shop I work at that we have to do a pinion seal on tomorrow and i can measure it real quick.
Im not sure. as long as it has a dana 80 and nv4500 I ASSUME it would be the same.
Id imagine this should not be too difficult for seth I am hoping to drop the shaft off tomorro though.

[killed300ex]

[QUOTE=Jim;47449]
I need to add some inches to the rear one. Do you have any experience with rebuilding the front with the double cardigan joint? If so i will take u up on that offer as the one I have is pretty shot. the rear joints are almost new.
QUOTE]

I just had mine rebuilt :omg: 3 joints plus that peice in the middle and an hour of labor at the machine shop. making me consider a 2wd :smilielol:

[95ctd]

Seth can't do that sorta stuff, he took electronics shop. :poke: :falldownlaugh:
when your drunk like i was last night its all the same, ps grains is good eatin, yes i eat alcohol:falldownlaugh:
57 5/8 on my truck but a dana 80 might change that

yeah dana 80 will shorten it up some, I think about 1 1/2" thanks evan
i got 56 5/16 so yeah bout 1 1/2 shorter

[Jim]

when your drunk like i was last night its all the same, ps grains is good eatin, yes i eat alcohol:falldownlaugh:



i got 56 5/16 so yeah bout 1 1/2 shorter
ok thanks! :HoleShotHolset:

[ktmcowboy]

Well, ill let you stick to the rear yourself, i dont want to screw with that haha. i probably could do it haha. But yea, I can rebuild em all. I have to do my front as well. I think that one is worst for me, cuz where the front half and the back half meet, there is like probably a quarter inch or so of play. but i plan on heading down this week as long as his schedule isn't too hectic. they are inducing labor on his wife on either monday or tuesday, so i might have to wait a few days. but would be glad to do it for ya.