Dyno Day @ Mass Diesel Nov 19th

[JakeBrakeIH]

Figured I'd pass the word, dyno day at Mass Diesel November 19th. It was a great time last year and should be again this year. :HoleShotHolset:

[Sledheadxp800r]

Im thinking about going. I have to try to break the 500 mark once more before the end of the year

[jdc753]

I had seen something about this on a Ford site last week and then couldn't find anything about it but I guess its true. Was great last time, hopefully show up again this year.

[95ctd]

Details.:exactly:

What time it starts and $ for how many rolls would be a good starting place

[JakeBrakeIH]

Details.:exactly:

What time it starts and $ for how many rolls would be a good starting place

Not much to a dyno day so not sure how much detail ya need:falldownlaugh:. Starts at 9am and I would assuming about $80 bucks for three pulls.

[Jays02F250]

Details.:exactly:

What time it starts and $ for how many rolls would be a good starting place

:withstupid:

[JakeBrakeIH]

:withstupid:

Starts at 9am and I would assuming about $80 bucks for three pulls.

What other info do you guys need?

[jdc753]

Scotts new Address for those who don't want to look it up or don't already know...

179 Mechanic St Bellingham, MA 02019
(508) 657-1951

Just a few miles off of 495, little further south than the old Walpole shop.

[95ctd]

Not much to a dyno day so not sure how much detail ya need:falldownlaugh:. Starts at 9am and I would assuming about $80 bucks for three pulls.

What other info do you guys need?

About isn't a definite I'd hate to show up with not enough money. If you could find that out that be great:HoleShotHolset:

[JakeBrakeIH]

About isn't a definite I'd hate to show up with not enough money. If you could find that out that be great:HoleShotHolset:

Do you plan on showing up with exact change? Put a $150 bucks in your pocket and you'll be set. Im just relaying the message, Ill see if I can find out.

[madmax66]

i shall be there to cheer on ppls :falldownlaugh:

[dieseldrunk]

I think its $75-80 for 3 spins, depends how many trucks are running, Shoot Scott an e-mail he's on this site.

[massdiesel]

Guys its 80.00 for 3 pulls if you need more pulls its all ok unless their is a bunch waiting to go on .Not anything Big I dont think we havent got any big response as of yet.A local bunch of gm guys asked and had a good crowd last year and was a great time.So figured before dyno goes inside for winter to be setup in its other location we would do it.Hope to see you guys !

Will start around 9-10 this is all weather pending obviously.

[dieselnomad]

:idea: cool. i'm going to try and make it. thanks... :HoleShotHolset::anitoof:

[95ctd]

same with me been trying to get my truck on the rollers for quite sometime its just never in one piece to do so:smilielol:

[scarboroughhb22]

ill be there im new to norwood im from maine so cant wait to meet some of you massholes:HoleShotHolset:

[95ctd]

same with me been trying to get my truck on the rollers for quite sometime its just never in one piece to do so:smilielol:
Might have jinxed myself by posting that:nutkick:

[02cumminsboy]

Hoping to not work so I can finally see what mine makes so I can stop guessing and see how far from my guess I am, then time to go bigger.

[Jim]

This coming sat Nov 19th the dyno will be set up from 9-5 at our shop in Bellingham.Its a anything goes for any vehicle type to run if anyone is interested.Dyno will be put inside at another ocation for the winter for indoor use.


Cost is 80.00 for 3 runs.

If weather is poor we will not be doing it if you are interested in coming please let us know.

Scott Hovey

[inlinepwr]

i'm gonna try to make it as long as i can get my oil changed.

[01dodgediesel]

great turn out over 20 trucks dynoed. some high number and some low numbers all an all it was a good time and was run smoothly. one of the better dyno day i have been to.
thanks scott for holding the event:HoleShotHolset:

[Sledheadxp800r]

Good time and strong Duramax showing. I was able to reach my goal for the year with my stock turbo Duramax. It put down 514hp 1015ft lbs

[massdiesel]

Thanks to all that came was a easy laid back day and fun.I am suprised at the Dmax count and very impressive numbers.Also not sure who was here for it but James dows truck is the baddest Dmax I have ever dynoed.James deserves alot of respect truck is built and tuned by himself and a very nice guy as well.

[Jim]

nice to hear there was a good turnout!

[dieseldrunk]

Thanks to all that came was a easy laid back day and fun.I am suprised at the Dmax count and very impressive numbers.Also not sure who was here for it but James dows truck is the baddest Dmax I have ever dynoed.James deserves alot of respect truck is built and tuned by himself and a very nice guy as well.

A well sorted truck for sure, over 800hp on the dyno, I missed his pull, enjoyed the day thanks to all the crew,

[madmax66]

i had a great time as well first time i've left a dyno not depressed!

:falldownlaugh:

[inlinepwr]

does anyone have any videos.:popcorn: i got called in to work so i couldn't make it, i guess i'll have to wait till next year.

[xcablb7]

Thanks to all that came was a easy laid back day and fun.I am suprised at the Dmax count and very impressive numbers.Also not sure who was here for it but James dows truck is the baddest Dmax I have ever dynoed.James deserves alot of respect truck is built and tuned by himself and a very nice guy as well.

just came across this site and this post, scott thank you very much i appreciate the kind words and credit. Lets see how she fairs at diesel power challenge

[Jim]

Good luck to ya and welcome to the site! Joel jsf350 from New hampshire was in last years challenge and is on the site also :HoleShotHolset:

[Jays02F250]

He took 3rd see if ya can beat him :poke::stirthepot: