Tranny ?? 48re

[BelgianMagic]

can I change the T/C and input shaft myself ...of do I need to have the tranny done somewhere?...problem is I only have the 1 vehicle...no spare so I don't wanna loose the truck for more than a day

throw me your input ,thanks.,Flip

[TORQUE THIS]

TC yes, input shaft, No...

[95Cummins]

Run the old Mack while your truck's in the shop, Flip :exactly: :falldownlaugh:

[BelgianMagic]

Run the old Mack while your truck's in the shop, Flip :exactly: :falldownlaugh:

7-8 MPG $3.29 a gallon =:omg::wtf2:

[Jim]

if you need it done in a day take it to a shop, IMHO.

[Schoust]

When I did my trany it did not look that hard to do at all,but if you are pulling it appart to that leval you might wqant to do more work if it's been a long while.......

[Ben@npd]

can I change the T/C and input shaft myself ...of do I need to have the tranny done somewhere?...problem is I only have the 1 vehicle...no spare so I don't wanna loose the truck for more than a day

throw me your input ,thanks.,Flip

This is something that can be done by anyone with good mechanical skills. You just have to make sure you have the tools and shims required to check and/or set end play. New shafts are usually very close, but its smart to check and adjust if needed.

[BelgianMagic]

I'm thinking ...the triple discTC and billet input....

WHAT ELSE should I do ? I haven't broken anything 'YET'

Except the 'lock' on the TC ... she slips in high gear with the Box...BUT NOT without

Back to stock - I think it would slip if I was hauling heavy though

[Ben@npd]

3DTC and billet input sound about right, but you need a VB to provide the needed pressures to save the rest of the clutches

[BelgianMagic]

Any Idea how much that would cost and is it a 1 day job ?:dunno:

[Ben@npd]

Are you interested in cost for labor only or parts also?
I would charge $650.00 for labor to install t.c. v.b. and input shaft
I dont know what brand part you want, but I sell Suncoast and Goerend stuff

[BelgianMagic]

DEFF Dave Goerend

[Schoust]

I simply picked up the phone talked to Dave about what I had in mind and how much power I was going to make and he told me what he would do and I said lets do it. The only thing I wish I had the money for was the Billet shafts,somhow I know I am going to regret that desision....

[Warpig]

Flip, you should also do a rebuild kit of all the soft parts while it's apart.

[BelgianMagic]

What would the "SOFT PARTS" consist of??

I haven't worked on a tranny in 30 years...so I will need to have someone do it for me

wonder what that will cost?? BUT I HAVE CAPITAL ONE in my wallet !:Paully6::woohoo::smilielol:

[TORQUE THIS]

What would the "SOFT PARTS" consist of??



Oh that's too easy... I'll pass on this one. :falldownlaugh:

[BelgianMagic]

Mark, what like seals and stuff ?? I only worked on manual trannys b4:Paully6:

[95Cummins]

I haven't worked on a tranny in 30 years... But I did stay at a Holliday Inn Express last night

:falldownlaugh: :exactly:

[BelgianMagic]

Boy dont make me hit you :Paully6::Paully6: too late:smilielol:

Flip>>>:whack:<<<<DAVE